Daewoo Nexia

Since 1994 of release

Repair and car operation


Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
- The engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance service and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation in gathering
   2.6. Engine support
   2.7. An inlet collector and a lining
   2.8. A final collector and a lining
   2.9. A cover of the case of a cam-shaft
   2.10. A pulley of a cranked shaft
   2.11. A forward cover of a gear belt
   2.12. A camshaft cogwheel
   2.13. A cogwheel of a cranked shaft
   2.14. A back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Check of angular position of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. A camshaft. Levers. Hydrojacks of backlashes
   2.19. Klapannye springs. Consolidations of cores of valves
   2.20. A head of cylinders. The camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of apertures of plugs
   2.25. Valves
   2.26. Klapannye springs
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of backlashes
   2.31. The oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. The oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. A flywheel. Back consolidation of a cranked shaft
   2.37. A cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. The block of cylinders
   2.43. Installation of pistons
   2.44. Balancing of a disk with a gear wreath
   2.45. Repair of carving apertures
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






2.43. Installation of pistons
THE GENERAL DATA

Place of gauging of diameter of the cylinder

 

Piston measurement

КОНУСНОСТЬ the PISTON. To measure diameter of the piston at level of an axis of an aperture under a finger and diameter of a skirt.

DIAMETER of the PISTON. To measure diameter of the piston in section which is below an aperture axis under a finger on 19 mm.
The prevention

At installation of pistons it is necessary to check up piston landing in the cylinder. Factory pistons and the pistons delivered as spare parts, have identical weight and can be established in the Engine without preliminary sorting and selection for weight Steadiness of the engine is not broken. If necessary it is possible to establish in separate cylinders and the pistons which were in the use if they are in a good condition.

In order to avoid infringement of steadiness of the engine it is forbidden to grind pistons for smaller diameter.

Identification number of diameter of cylinders is put down about identification number of the engine.

To measure
PERFORMANCE ORDER
1. The piston. At deterioration or presence of other defects to replace with the piston of normal or increased diameter.
2. A cylinder aperture, fig. the Place of gauging of diameter of the cylinder. If necessary to restore working capacity расточкой and хонингованием for the repair size.
The prevention

Definitively to finish diameter of the cylinder хонингованием after piston selection.

3. To establish the piston in the cylinder.
The prevention

The piston and cylinder mirror should be dry.

4. Carefully to wash out a brush with a soap solution a mirror of the cylinder and the piston. To remove all alien particles. To dry and grease with pure engine oil.
5. To check up piston landing in a cylinder aperture.
5а. To measure diameter of the cylinder by a micrometer with a telescopic bar.
5б. To measure diameter and конусность the piston, fig. piston Measurement.
5в. To subtract diameter of the piston from diameter of the cylinder for backlash definition.
5г. To compare the received value of a backlash to the demanded.
5д. To define suitability of the piston for the given cylinder.
6. If the piston which was in the use does not approach, to pick up the new piston. (In spare parts pistons both normal, and the increased repair sizes) are delivered.
7. If the cylinder mirror is subject to processing, it is necessary to measure the new piston and to finish хонингованием diameter of the cylinder till the necessary size.
8. To mark the new piston with a cylinder serial number for which it is intended. (On some engines pistons with diameter increased by 0,25 mm) can be established.
9. Carefully to wash out a brush with a soap solution a mirror of the cylinder and the piston. To remove all alien particles. To dry and grease with pure engine oil.