Daewoo Nexia

Since 1994 of release

Repair and car operation



Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
- The engine
   2.1. Technical characteristics
   2.2. Greasing system
   2.3. Maintenance service and engine repair
   2.4. Compression check
   2.5. Dismantle and engine installation in gathering
   2.6. Engine support
   2.7. An inlet collector and a lining
   2.8. A final collector and a lining
   2.9. A cover of the case of a cam-shaft
   2.10. A pulley of a cranked shaft
   2.11. A forward cover of a gear belt
   2.12. A camshaft cogwheel
   2.13. A cogwheel of a cranked shaft
   2.14. A back cover of a gear belt
   2.15. Adjustment of a tension of a gear belt
   2.16. Check of angular position of a camshaft
   2.17. Forward consolidation of a cranked shaft
   2.18. A camshaft. Levers. Hydrojacks of backlashes
   2.19. Klapannye springs. Consolidations of cores of valves
   2.20. A head of cylinders. The camshaft case
   2.21. Repair of a head of the block of cylinders
   2.22. Dismantle of valves
   2.23. Directing plugs of valves
   2.24. Expansion of apertures of plugs
   2.25. Valves
   2.26. Klapannye springs
   2.27. Saddles of valves
   2.28. Consolidations of valves
   2.29. Height of a core of the valve concerning a head of the block of cylinders
   + 2.30. Pushers of valves with hydrojacks of backlashes
   2.31. The oil pallet
   2.32. A reception branch pipe with the oil filter
   2.33. The oil pump
   2.34. Repair of the oil pump
   2.35. Pistons and rods
   2.36. A flywheel. Back consolidation of a cranked shaft
   2.37. A cranked shaft
   2.38. Rods and radical bearings
   2.39. Replacement of loose leaves
   2.40. Piston group and rods
   2.41. Piston fingers and rings
   2.42. The block of cylinders
   2.43. Installation of pistons
   2.44. Balancing of a disk with a gear wreath
   2.45. Repair of carving apertures
   + 2.46. Diagnostics of malfunctions of the engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






2.35. Pistons and rods To remove or disconnect

PERFORMANCE ORDER
1. The oil pallet 125, the oil pump 137, a head of cylinders 29.
2. To lower the piston 160 in the lowest position. To remove a fillet on a cylinder mirror.
3. To uncover 157 bottom heads and loose leaves 158 шатунного the bearing. Preliminary to mark details with a cylinder serial number.
4. A rod 159 with the piston 160. To establish preliminary on шатунные bolts protective plugs. To clear an internal surface of cylinders by means of a fabric moistened in oil.

To establish or attach

PERFORMANCE ORDER
1. Pistons 160 with rods 159.
To establish the piston in assembly adaptation J-8037 for compression of piston rings and to shift it in the cylinder, slightly tapping on the piston bottom. The arrow on the piston bottom should be directed to a forward part of the engine. To establish rods 159 on necks of a cranked shaft 119.
The prevention

Before assemblage to grease all details.


2. To establish loose leaves 158 шатунных bearings and to fix covers of 157 rods (according to their preliminary marks).
The prevention

Loose leaves, shaft and cover necks should be oiled. To use only new шатунные bolts.


3. To tighten шатунные bolts the moment of 25 Nanometers, then in addition to tighten turn on 30 .
4. The oil pump 137, the oil pallet 125, a head of cylinders 29.