Daewoo Nexia

Since 1994 of release

Repair and car operation



Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral молдинги
   18.4. Diagnostics and repair негерметичности Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   + 18.8. Back glass (the Body a sedan)
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination негерметичности consolidations
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. Вентиляционнай the valve (the Body a hatch-back)
   18.35. Лючок mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment






18.3. Pasted lateral молдинги
THE GENERAL DATA

Repair молдингов on lateral panels of the Body


Lateral молдинги fasten to Body panels, by means of gluing structure. For strong fastening молдингов (old or new) it is necessary, that the surface of panels was pure and free from traces of wax or an oil film, and the temperature of panels was between 21 With and 32 With.

Подклейка молдинга

PERFORMANCE ORDER
1. To wash out the damaged place a soap solution and to wipe dry. To wipe a surface of the panel and the contact party of holding a fabric moistened in pure kerosene or spirit. If the decorative part молдинга has departed from the pasted basis (which remains on the Body), the last should not be removed. To clear by means of kerosene (not containing oil) or surface spirit прилегания the bases of a decorative part молдинга.
2. To paste on the panel directing tape of day of correct placing молдинга (if necessary).
3. To put on a contact surface молдинга glue and to press молдинг to the panel. At use of gluing structure of mark Loclite 414 (or an equivalent substitute) to sustain молдинг under loading during 30 with or before formation of strong connection.

Gluing молдинга

PERFORMANCE ORDER
1. To wash out the damaged panel a soap solution and to wipe dry. To remove all rests of glue from a surface of the panel and the contact party молдинга by means of pure kerosene (not containing oil) or spirit.
2. To plan an arrangement молдинга for panels of the Body by means of a directing tape. Thus it is necessary to be guided by position next молдинга.
3. If the temperature of the panel of the Body does not exceed 21 With, it is necessary to heat up the panel by means of reflex lamps or warm air.
4. To put on молдинг акриловый gluing structure (for example, marks ЗМ).
5. To put молдинг to the panel and strongly to press.