Daewoo Nexia

Since 1994 of release

Repair and car operation



Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
- Body
   18.2. Identification and use of keys
   18.3. Pasted lateral молдинги
   18.4. Diagnostics and repair негерметичности Bodies
   18.5. Anticorrosive processing
   + 18.6. Dismantle of consolidations of wind and back glasses
   + 18.7. A windscreen
   - 18.8. Back glass (the Body a sedan)
      18.8.1. Windscreen consolidation
   18.9. Glass of a back door (the Body a hatch-back)
   18.10. Triangular lateral glass
   + 18.11. Elimination негерметичности consolidations
   + 18.12. A rear-view mirror
   + 18.13. An electroheater of back glass
   + 18.14. Bumpers
   18.15. An external ventilating lattice
   18.16. The switch of a forward door
   18.17. A cowl
   18.18. Cowl loops
   18.19. A cowl emphasis
   18.20. The zapornoe device of a cowl
   18.21. A safety latch of a cowl
   18.22. A cable of a latch of a cowl
   18.23. A radiator lattice
   18.24. A forward wing
   + 18.25. Panels of an upholstery of doors
   + 18.26. The equipment of doors (forward and back doors)
   + 18.27. Door-locks
   + 18.28. Glasses of doors
   18.29. External rear-view mirrors
   18.30. Dismantle and installation of forward and back doors
   + 18.31. Back panels of an upholstery (the Body a hatch-back)
   + 18.32. Upholstery panels (the Body a sedan)
   18.33. The external panel
   18.34. Вентиляционнай the valve (the Body a hatch-back)
   18.35. Лючок mouths of a fuel tank
   + 18.36. Opening window leaves (the Body a hatch-back)
   + 18.37. A back shelf (the Body a sedan)
   18.38. A luggage space cover (the Body a hatch-back)
   18.39. An overlay of a back wall of a luggage carrier (the Body a sedan)
   + 18.40. A luggage carrier cover (the Body a sedan)
   18.41. The back combined lantern
   + 18.42. A back door (the Body a hatch-back)
   18.43. A roof
   18.44. The ceiling panel
   18.45. Protivosolnechnye peaks
   18.46. A plafond of internal illumination
   + 18.47. Panels and the salon equipment
   18.48. External longitudinal overlays of a roof
   + 18.49. The ventilating hatch
   + 18.50. Forward seats
   + 18.51. A back seat
+ Heating, ventilation
+ Electric equipment






18.8. Back glass (the Body a sedan)

18.8.1. Partial replacement of a glutinous fringing
THE GENERAL DATA

Section of consolidation of back glass

1. BACK GLASS
2. CONSOLIDATION

Emphasis of back glass

1. BACK GLASS
2. THE EMPHASIS OF BACK GLASS

To remove or disconnect

Dismantle of consolidation of back glass (the Body a sedan)

1. CONSOLIDATION
2. THE EMPHASIS OF BACK GLASS
3. BACK GLASS

Windscreen dismantle

1. THE STRING

PERFORMANCE ORDER
1. To remove manually a decorative overlay of back glass. In order to avoid damage of a paint and varnish covering to stick together a sticky tape elements of the Body directly adjoining to back glass.
2. To disconnect electroconducting from a heater of back glass.
3. By means of a knife for sealant removal to make an incision the parties and sealant top as it is possible more close to an edge of back glass.
4. The emphasis of back glass located at the bottom edge, fig. the Emphasis of back glass. To insert outside a string between glass and the Body and by means of the second mechanic to cut off a glutinous layer on the bottom edge of back glass.
5. Back glass from the car.

To clear

PERFORMANCE ORDER
1. An aperture of a window from the rests of all materials.
2. Glass on perimetre of an edge for the subsequent drawing of preparatory layers.
3. To wipe a windscreen the pure fabric moistened in spirit.

To establish or attach

Windscreen installation

Drawing on a windscreen of priming structure

1. THE NEW BRUSH
2. STRUCTURE FOR PRIMING COAT DRAWING

Drawing герметизирующего structure

 

PERFORMANCE ORDER
1. By means of a new brush to put on edge has flown down preparatory layers, using corresponding structures from a repair set. At first it is necessary to put грунтовоч ный a layer from transparent structure, and then – from structure of black colour. Priming coats put on perimetre of an edge of glass (glass from the inside) a strip the in width of 6 mm. To put equal, непрерыв ный the platen of gluing structure on perimetre of glass and over priming coats.
At partial replacement of a fringing the thickness of the platen should make 5 mm.
At full replacement of a fringing the thickness of the platen should make from 8 to 10 mm.
2. An emphasis of back glass.
3. Back glass in a window aperture by means of the second mechanic. To centre glass in a window aperture. Use of rubber suckers can facilitate glass installation, fig. windscreen Installation. To press a glass emphasis in a direction to the car centre that back glass has occupied correct position.
4. Молдинг back glass, having pressed it by hand.
5. To check up герметиченость consolidations of back glass, watering. At detection негерметичности it is necessary to dry glass and in addition to impose герметизирующий structure. If it was not possible to eliminate a leak, it is necessary to remove glass and to repeat all installation anew.
The prevention

It is not necessary to direct on свежеположенный hermetic a strong stream of water. The water which has got on a surface of hermetic, promotes polymerisation acceleration уретана.