Daewoo Nexia

Since 1994 of release

Repair and car operation

Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
- Transmission
   9.2. The general description
   9.3. Diagnostics of malfunctions
   9.4. A cable of a drive of coupling
   9.5. A coupling pedal
   9.6. Conducted and press disks, a coupling drive
   9.7. Removal of air from a hydraulic drive of coupling
   9.8. The main cylinder
   9.9. The working cylinder of coupling
   9.10. The basic malfunctions of coupling, their reason and ways of elimination
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment

Soap2 day

9.7. Removal of air from a hydraulic drive of coupling

THE GENERAL DATA

Coupling with a hydraulic drive

1. THE PLATEN WITH THE LEVER OF DEENERGIZING OF COUPLING
2. THE BOLT
3. THE SPRING WASHER
4. THE BOLT
5. THE FLAT WASHER
6. THE NUT
7. THE BOLT
8. THE ARM OF THE WORKING CYLINDER
9. THE WORKING CYLINDER
10. THE COPPER WASHER
11. THE BOLT
12. THE HOSE WITH TIPS
13. THE ARM
14. THE CLIP
15. THE PIPELINE
16. THE MAIN CYLINDER
17. THE COPPER WASHER
18. THE HOSE UNION
19. THE SPRING COLLAR
20. THE TANK
21. THE HOSE
22. THE BOLT
23. THE TANK ARM
24. THE NUT
25. THE FINGER
26. THE CLIP
27. THE RETURNABLE SPRING
28. THE PLUG
29. THE TERMINATOR OF THE COURSE PEDALS (TOP)
30. THE COUPLING PEDAL 31. THE PEDAL OVERLAY
32. THE AXIS
33. THE WASHER
34. THE NUT
35. SPRING ШПЛИНТ
36. THE PEDAL ARM
37. THE BOLT
38. THE COUNTERNUT
39. THE FLANGE
40. THE PALLET
41. THE BOLT
42. CONSOLIDATION OF THE PRIMARY SHAFT
43. THE SEALING RING
44. DIRECTING PLUG VYZHIMNOGO OF THE BEARING
45. ВЫЖИМНОЙ THE BEARING
46. THE PLUG
47. THE PLUG
48. THE WASHER
49. THE BOLT
50. THE CONDUCTED DISK
51. THE CASING OF COUPLING WITH THE PRESS DISK AND THE SPRING
52. THE WASHER
53. THE BOLT
54. THE PLUG BOLT
55. THE NUT
56. THE PLUG
57. THE ROD
58. THE COUNTERNUT
59. THE VALVE FOR AIR REMOVAL

Removal of air from a coupling hydrodrive

9. THE WORKING CYLINDER
59. THE VALVE FOR AIR REMOVAL

PERFORMANCE ORDER

1. After end of repair and assemblage of a hydraulic drive it is necessary to remove from it air.

2. In the course of prorolling of a hydrodrive for air removal it is necessary to support in a tank level of a working liquid not below label MIN.

3. To put on the valve of release of air the end of a vinyl hose. Other end of a hose to lower in transparent capacity, наполови well filled with a brake liquid.

4. Some times slowly to press a coupling pedal.

5. At the pressed pedal of coupling partially to turn on the valve for air release. After the termination вытекания liquids from the hose which has been put on the valve to wrap the valve.

6. To repeat operations 4 and 5 some times while air vials will not cease to leave together with a working liquid.

7. After prorolling end гидроприво yes to add in a tank a brake liquid and to finish its level to a label the MOVE.