Daewoo Nexia

Since 1994 of release

Repair and car operation


Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
- Transmission
   9.2. The general description
   9.3. Diagnostics of malfunctions
   9.4. A cable of a drive of coupling
   9.5. A coupling pedal
   9.6. Conducted and press disks, a coupling drive
   9.7. Removal of air from a hydraulic drive of coupling
   9.8. The main cylinder
   9.9. The working cylinder of coupling
   9.10. The basic malfunctions of coupling, their reason and ways of elimination
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






9.5. A coupling pedal
THE GENERAL DATA

Fastening of a tip of a cable to the lever of deenergizing of coupling

2. THE CLIP
3. THE CABLE TIP
4. THE NUT

Fastening of a pedal of coupling

7. ШПЛИНТ
8. THE NUT
9. THE WASHER
11. THE AXIS
12. THE RETURNABLE SPRING

Cable fastening to a coupling pedal

3. HAKOHEЧНИK THE CABLE
12. THE RETURNABLE SPRING
14. THE PEDAL

To remove or disconnect

PERFORMANCE ORDER
1. A negative wire of the storage battery.
2. To measure free length of a carving tip of a cable. To write down result of measurement.
3. A tip of a cable 3 from the lever of the platen of 1 deenergizing of coupling.
3а. To remove a clip 2.
3б. To turn away a nut 4.
4. The switch of blocking of start of the engine.
5. A coupling pedal.
5а. A returnable spring 12 from a kerchief 10.
5б. Шплинт 7.
5в. A nut 8.
5г. A washer 9.
5д. An axis 11.
5е. A pedal 14.
6. A returnable spring 12 and a tip of a cable from a pedal 14.

To establish or attach

PERFORMANCE ORDER
1. To attach a tip of a cable and a returnable spring 12 to a pedal 14.
2. To grease an axis 11 консистентной with greasing N 1052349 or equivalent.
3. To establish a pedal 14 between kerchiefs 10 steering columns.
4. To insert into apertures of kerchiefs 10 and pedals 14 axis 11.
4а. To put on a washer 9.
4б. To screw a nut 8.
4в. To insert шплинт 7.
4г. To insert a returnable spring 12 into a kerchief 10.
5. The switch of blocking of start of the engine.
6. A tip 3 cables to the lever of the platen of 1 switch of coupling.
7. To screw a nut 4 in position with which it occupied before cable dismantle.
8. To adjust a drive cable.
9. A clip 2.
10. A negative wire of the battery.

To adjust (with тросовым a drive)

PERFORMANCE ORDER
1. To release a counternut 38 and rotation of a bolt 37 to adjust a pedal course.
2. To adjust a pedal free wheeling, having released a counternut 58 and rotating a rod 57. The nominal size of a free wheeling of a pedal is equal 8–15 mm.
3. After adjustment to tighten a counternut 58.
4. To check up size of a free wheeling of a pedal as follows. To press a pedal a hand with small effort and to measure moving of a pedal from initial position before position when resistance to pedal moving starts to increase.

To adjust (with a hydraulic drive)

PERFORMANCE ORDER
1. To include a lay brake.
2. To start the Engine and to deduce it on idling.
3. Having made small effort to the lever of a transmission for inclusion of transfer of a backing, slowly to press a coupling pedal. To measure distance from the position of a pedal corresponding to the termination of a gnash of teeths of included gear wheels, before extreme position of completely pressed pedal. This distance should exceed 25 mm.
4. If the result of measurement does not correspond to the specified requirement, it is necessary to check up the following:
– Height of an arrangement of a pedal of coupling;
– Size of a free wheeling of a pedal of coupling;
– Air presence in a coupling hydrodrive;
– A condition of a disk of coupling.