Daewoo Nexia

Since 1994 of release

Repair and car operation



Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
- Brake system
   17.2. The general description
   17.3. Check of a technical condition of brake system
   17.4. Filling of a tank of the main brake cylinder
   17.5. Removal of air from brake system
   17.6. Washing of brake system
   17.7. Check of a regulator of brake forces
   17.8. Brake hoses (lobbies)
   17.9. Brake hoses (back)
   + 17.10. A lay brake
   17.11. Check of a condition of forward brake overlays
   17.12. Check of a condition of back brake overlays
   17.13. Brake disks
   17.14. Brake drums
   17.15. A brake pedal
   17.16. The main brake cylinder
   17.17. A tank
   17.18. Regulators of brake forces (proportional valves)
   17.19. The main brake cylinder in gathering
   17.20. Repair of the main brake cylinder
   17.21. The disk brake mechanism
   17.22. Колодки and overlays
   17.23. A protective cover of the piston
   17.24. A brake disk
   17.25. A support
   17.26. A guard
   17.27. Support repair
   17.28. The drum-type brake mechanism
   17.29. Adjustment of the brake mechanism
   17.30. Adjustment of a lay brake
   17.31. A basic brake disk
   17.32. The wheel cylinder
   17.33. Repair of the wheel cylinder
   17.34. The vacuum amplifier of brakes
   + 17.35. Antiblocking system of brakes
   17.36. Removal of air from a brake hydraulic drive
   17.37. Removal of air from a brake hydraulic drive manually
   17.38. The valve for removal of air from the block of modulators
   17.39. Electromagnetic valves of modulators
   17.40. The block of hydraulic modulators with electric motors
   17.41. The electronic block of management of braking
   17.42. The gauge of angular speed of a forward wheel
   17.43. Flexible conducting ДУС of a forward wheel
   17.44. The gauge of angular speed of a back wheel
   + 17.45. Flexible conducting ДУС of a back wheel
   17.46. A system electric safety lock
   17.47. Relay ABS
   17.48. Signalling devices
+ Body
+ Heating, ventilation
+ Electric equipment






17.4. Filling of a tank of the main brake cylinder
THE GENERAL DATA

The prevention

It is forbidden to apply the brake liquids made on a mineral basis. It is not necessary to use also capacities in which mineral oils, mineral brake liquids or water contained. The impurity of mineral oil or a liquid will lead to swelling and failure of rubber consolidations. Water hit will cause decrease in temperature of boiling of a brake liquid and refusal of brake system at intensive braking. Capacities with a brake liquid should be stored tightly closed and at opening to protect from dirt and water hit. Level of a brake liquid in a tank of the main cylinder should be supported constantly in norm. It provides normal work of a hydrodrive and excludes air and moisture hit in system. However it is not necessary to overflow a tank as the brake liquid should have expansion possibility at heating from heat allocated in brake mechanisms and radiated by the engine.


The tank is located on the main brake cylinder: under a cowl at the left on a forward board of the Body. Before opening a tank cover, it should be wiped carefully from a dirt. To open a cover and to finish level of a brake liquid to norm, being guided by a label outside of a tank. It is recommended to apply a brake liquid of mark Delco Supreme N11 or equivalent to it. It is authorised to apply a brake liquid only type "DOT 3".