Daewoo Nexia

Since 1994 of release

Repair and car operation


Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






3.9. Engine support
THE GENERAL DATA

Traverse for engine fastening

 
The prevention

In avoidance травмирования it is necessary to watch closely correctness of installation and reliability of fastening of the engine to technological a traverse (adaptation KM-263), established over a motor compartment.

Defective support of the engine should be replaced at once new in order to avoid failure of other support and other details.

To check up

PERFORMANCE ORDER
1. To raise the Engine, to unload rubber pillows of support.
2. A surface of rubber pillows on presence of cracks because of an overheat.
3. Backlog of rubber pillows from plates.
4. Presence of cracks and ruptures of rubber in the middle of pillows.
5. Easing of an inhaling of bolts and nuts.

To remove or disconnect

PERFORMANCE ORDER
1. A negative wire of the storage battery.
2. To suspend the Engine on a traverse (adaptation KM-263).
3. A bolt of an arm of the right forward support.
4. A bolt of fastening of an arm of the right forward support to the engine block.
5. Nuts and washers of the right forward support.
6. Bolts of an arm of the left forward support.
7. Bolts of fastening of an arm of the left forward support to the engine block.
8. Bolts and washers of the left forward support.
9. A nut, a bolt, a washer and an arm of a back support.
10. Bolts, a washer and a back support of the engine from the car.