Daewoo Nexia

Since 1994 of release

Repair and car operation


Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
- 3. The engine (two top camshafts)
   3.2. The general description
   3.3. Work of hydraulic jacks of backlashes
   3.4. Greasing system
   3.5. Maintenance service and repair
   3.6. Compression check
   3.7. Dismantle and engine installation in gathering
   3.8. A klinovoj belt
   3.9. Engine support
   3.10. An inlet collector and a lining
   3.11. A final collector and a lining
   3.12. A cover клапанного the mechanism and a lining
   3.13. A pulley of a cranked shaft
   3.14. A forward cover of a gear belt
   3.15. A gear belt
   3.16. Натяжитель a gear belt
   3.17. A camshaft cogwheel
   3.18. A cogwheel of a cranked shaft
   3.19. A back cover of a gear belt
   3.20. Forward consolidation of a cranked shaft
   3.21. A camshaft. Hydrojacks of backlashes of valves
   3.22. A head of the block of cylinders
   3.23. Repair of a head of the block of cylinders
   3.24. Klapannye springs. Consolidations of cores of valves
   3.25. Dismantle of valves
   3.26. Directing plugs of valves
   3.27. Expansion of apertures of plugs
   3.28. Valves
   3.29. Klapannye springs
   3.30. Saddles of valves
   3.31. The oil pallet
   3.32. A reception branch pipe with the oil filter
   3.33. The oil pump
   3.34. Repair of the oil pump
   3.35. Pistons and rods
   3.36. A flywheel. Back consolidation of a cranked shaft
   3.37. A cranked shaft
   3.38. Rods and radical bearings
   3.39. Replacement of loose leaves
   3.40. Piston fingers and rings
   3.41. The block of cylinders
   3.42. Installation of pistons
   3.43. Balancing of a disk with a gear wreath
   3.44. Repair of carving apertures
   3.45. Diagnostics of malfunctions
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






3.22. A head of the block of cylinders
THE GENERAL DATA

Sequence отворачивания bolts of a head of the block of cylinders

 

Sequence of an inhaling of bolts of fastening of a head of the block of cylinders

 

To remove or disconnect

PERFORMANCE ORDER
1. A negative wire of the storage battery.
2. To merge cooling liquid.
3. A gear belt.
4. The inlet pipeline with a lining.
5. The final pipeline with a lining.
6. The ignition distributor.
7. A cover клапанного the mechanism with a lining.
8. Cam-shafts 19 and pushers 20.
9. Натяжитель 53 belts and an intermediate roller 55.
10. A hairpin of 68 covers of a gear belt.
11. Bolts of 30 fastenings of a head of cylinders.
The prevention

At first to unscrew all bolts of a head of cylinders on 1/4 turns in the sequence shown on fig. Sequence отворачивания of bolts of a head of the block of cylinders. Then in the same order to unscrew all bolts on 1/2 turns.

12. A head of cylinders 33.
13. To clear interfaced planes of a head and the block of cylinders.

To establish or attach

PERFORMANCE ORDER
1. A new lining 35 on the top plate of the block of cylinders.
2. A head of the block of cylinders on the block and to screw in bolts 30.
3. To tighten bolts of fastening of a head of cylinders the moment of 20 Nanometers, then to tighten bolts in three steps on 195 (on 65 at one time). An inhaling of bolts to make in the sequence specified in fig. Sequence of an inhaling of bolts of fastening of a head of the block of cylinders.
4. A hairpin of 68 covers of a gear belt.
5. Натяжитель 53 belts and an intermediate roller 55.
6. Pushers 20 and cam-shafts 19.
7. A cover 7 клапанного the mechanism with a lining 15.
8. The ignition distributor.
9. The inlet pipeline with a lining.
10. A gear belt.
11. To fill in cooling liquid.
12. A negative wire of the storage battery.