Daewoo Nexia

Since 1994 of release

Repair and car operation


Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
+ Steering
+ Running gear
- 14. A forward suspension bracket
   14.2. The general description
   14.3. Check of size of forces of a friction in a suspension bracket
   14.4. Condition check подшипниковых support and spherical hinges
   14.5. The stabilizer
   14.6. A rack in gathering with подшипниковой a support
   14.7. The bottom lever
   14.8. The spherical hinge
   14.9. A nave and the wheel bearing
   14.10. The top support
   14.11. Springs
   14.12. The shock-absorber
   14.13. Plugs of hinges of the bottom lever
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






14.7. The bottom lever To remove or disconnect

PERFORMANCE ORDER
1. To release bolts of fastening of forward wheels.
2. To lift the car.
3. To bring basic racks under the car.
4. To lower it is a little car so that he leant against racks, but not on the bottom levers.
5. Forward wheels.
6. The stabilizer from the bottom lever (a detail 8, 9, 10, 18, 19, 20, 21, 22, 28, 29. 30).
The prevention

To track that полуось did not leave the internal mobile hinge. It will lead to hinge dismantling. Probably also hinge damage. During work in a zone of an arrangement of hinges of semiaxes it is necessary to use the protective covers which are put on on rubber грязезащитные of consolidation of hinges. Otherwise damage of details or consolidations of hinges and an exit of hinges out of operation is possible.

7. A spring clamp 1 and a nut 2 spherical hinges 6.
8. The spherical hinge 6. At use of stripper КМ-507В for dismantle of spherical hinges it is not necessary to pay attention to an inscription "This party to a wheel", выштампованную on the adaptation.
9. Bolts 3, 11 fastenings of the bottom lever.
10. The bottom lever 13.

To establish or attach

Fastening of the bottom lever

 3. The BOLT. To USE NEW BOLTS. ON the CARVING to PUT HERMETIC. The MOMENT of the INHALING of 70 Nanometers.
11. THE BOLT. TO USE THE NEW BOLT. AT FIRST TO ESTABLISH
FORWARD BOLT. The MOMENT of the INHALING of 140 Nanometers.

PERFORMANCE ORDER
1. A bolt 11 and a washer 12.
2. Bolts of 3 fastenings of the back end of the lever 13.
The prevention

Nuts of fastening of the bottom lever should not be thus tightened.

3. The stabilizer to the bottom lever (to a detail 8, 9, 10, 18, 19, 20, 21, 22, 28, 29, 30).
4. The spherical hinge 6 on a rack 33 and a nut 2.
5. To raise the car so that it leant against the bottom levers.
The prevention

The inhaling of bolts and nuts of fastening of the bottom levers should be made at опирании the car on the bottom levers in static position of a suspension bracket which corresponds to the equipped weight of the car.

6. To tighten a nut of fastening of the stabilizer the moment of 17 Nanometers.
7. To tighten bolts of 3 fastenings of the back end of the lever the moment of 70 Nanometers.
8. To tighten a forward bolt of 11 fastenings of the lever the moment of 140 Nanometers.
9. To tighten a nut 2 spherical hinges the moment of 70 Nanometers.
10. A nut 2 and a spring clamp on a finger of the spherical hinge.
11. To remove a protective casing of consolidations of hinges of a semiaxis.
12. A wheel.
13. To raise it is a little car.
14. To remove basic racks.
15. To lower the car.
16. To tighten bolts of fastening of a wheel in a cross order the moment of 90 Nanometers.