Daewoo Nexia

Since 1994 of release

Repair and car operation



Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
- Steering
   12.2. The general description
   12.3. The reechnyj steering mechanism in gathering
   12.4. Tips of steering draughts
   12.5. Steering draughts
   12.6. A casing картера the steering mechanism
   12.7. Муфта a steering shaft
   12.8. A sealing cover of an aperture of a forward board of the Body
   12.9. Плунжер рейки
   12.10. The Shaft-gear wheel
   12.11. Рейка
   12.12. The needle bearing
   12.13. The directing plug рейки
   12.14. Check of neutral position рейки
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added a working liquid
   12.17. Removal of air from hydrosystem
   12.18. The steering mechanism with the hydraulic booster in gathering
   12.19. Hoses and pipelines
   12.20. A tank
   12.21. Tips of steering draughts
   12.22. Steering draughts
   12.23. Plugs of hinges of steering draughts
   12.24. Муфта a steering shaft
   12.25. A sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring плунжера
   12.28. Consolidations of a shaft of the hydrodistributor and the top bearing
   12.29. The steering mechanism
   12.30. Check of neutral position рейки
   12.31. A belt of a drive of the pump
   12.32. A pulley of a drive of the pump
   12.33. The pump in gathering
   12.34. Control levers on a steering column
   12.35. A steering wheel
   12.36. The ignition lock
   12.37. A steering column
   12.38. Lever the switch, a steering shaft, a steering column (noncontrollable)
   12.39. Lever the switch, a steering shaft, a steering column (regulated)
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






12.30. Check of neutral position рейки
THE GENERAL DATA

Check of installation of operated wheels in position for rectilinear movement

AND. THE BRAKE AMPLIFIER
CENTURY THE MAIN BRAKE CYLINDER
WITH. THE RETURN VACUUM VALVE

20. THE RUBBER ASSEMBLY PLUG
30. THE BOLT
44. CARTER'S CASING

After end of any repair work with the steering mechanism (dismantle and installation, dismantling and assemblage) it is necessary to check up neutral position рейки, corresponding to installation of operated wheels for rectilinear movement of the car.

To adjust

Position рейки, corresponding to rectilinear movement of the car

AND. AVERAGE POSITION РЕЙКИ

38. THE BOLT
40. STEERING DRAUGHT (RIGHT)
55. CARTER

Check of position of an axis of a coupling bolt муфты

AND. THE AXIS OF COUPLING BOLT МУФТЫ SHOULD SETTLE DOWN HORIZONTALLY

1. THE COUPLING BOLT
2. МУФТА THE STEERING SHAFT
20. THE RUBBER ASSEMBLY PLUG
35. STEERING DRAUGHT (LEFT)
38. THE BOLT
40. STEERING DRAUGHT (RIGHT)
44. CARTER'S CASING
55. CARTER

Check of correctness of assemblage of the steering mechanism

AND. WRONG ASSEMBLAGE OF THE STEERING MECHANISM (THE AXIS OF THE COUPLING BOLT IS NOT HORIZONTAL)

1. THE COUPLING BOLT
2. МУФТА
20. THE ASSEMBLY PLUG
35. STEERING DRAUGHT (LEFT)
40. STEERING DRAUGHT (RIGHT)
44. CARTER'S CASING

PERFORMANCE ORDER
1. To establish a lath of control and measuring adaptation KM-476 between heads of steering draughts. Thus the adaptation pin should enter into deepening of a seat left (in the direction of the car) the rubber plug.
2. To keep a steering wheel in position which corresponds to rectilinear movement of the car. At neutral position рейки the size And is equal 325 mm.
3. To check up observance of following conditions:
      – The coupling bolt клеммового соедине ния муфты should settle down from above a steering shaft, and its axis should be horizontal;
      – cпицы a steering wheel should be symmetrized concerning a vertical and to be directed downwards.
If the axis of a coupling bolt is located наклонно assemblage of the steering mechanism is made incorrectly (with displacement on one or several teeths рейки). In this case it is necessary to dismantle a shaft-gear wheel and anew to collect the mechanism.
If the coupling bolt муфты is located horizontally, and steering wheel spokes are asymmetrical concerning a vertical (отклоне ние makes more than 5 degrees), it is necessary to remove a steering wheel from a steering shaft, to centre and establish it anew.