Daewoo Nexia

Since 1994 of release

Repair and car operation

12.3. The reechnyj steering mechanism in gathering

THE GENERAL DATA

The reechnyj steering mechanism

1. COUPLING BOLT МУФТЫ 2. МУФТА 3. The SEALING COVER of the APERTURE of the FORWARD BOARD of the Body 4. SHAFT-GEAR WHEEL CONSOLIDATION 5. THE SHAFT-GEAR WHEEL IN GATHERING 6. THE NEEDLE BEARING 7. CARTER OF THE STEERING MECHANISM 8. ЗАГЛУШКА CARTER (LEFT) 9. THE RUBBER ASSEMBLY PLUG 10. DIRECTING PLANCK РЕЙКИ 11. THE SPRING RING 12. IT IS NOT USED 13. THE BOLT (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION) 14. THE COLLAR (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION) 15. THE NUT (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION) 16. THE CASING PLUG 17. THE CASING COLLAR 18. THE ADJUSTING SCREW 19. THE TIP OF STEERING DRAUGHT (LEFT) 20. THE SEALING COVER 21. THE NUT 22. THE COUPLING BOLT

23. STEERING DRAUGHT (LEFT) 24. THE FIXING PLATE 25. THE BOLT 26. THE BASIC PLATE (ONLY FOR CARS WITH THE MANUAL TRANSMISSION) 27. PLUG SHARNIPA OF STEERING DRAUGHT 28. THE TIP OF STEERING DRAUGHT (RIGHT) 29. STEERING DRAUGHT (RIGHT) 30. THE WASHER 31. THE CASING COLLAR 32. CARTER'S CASING 33. ДЕМПФЕР THE STEERING (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION) 34. РЕЙКА 35. ЗАГЛУШКА CARTER (RIGHT) 36. THE RUBBER ASSEMBLY PLUG 37. THE CASING PLUG 38. THE SPRING RING 39. DIRECTING PLUG REJKI 40. ПЛУНЖЕР 41. THE SEALING RING 42. THE SPRING 43. THE ADJUSTING STOPPER 44. THE COUNTERNUT

Муфта a steering shaft

1. THE COUPLING BOLT 2. МУФТА IN GATHERING

To remove or disconnect

Fastening реечного the steering mechanism

45. THE BOLT 46. THE COLLAR OF FASTENING OF CARTER

PERFORMANCE ORDER

1. A negative wire of the storage battery. 2. To lift and properly to fix the car. 3. To turn out two coupling bolts 1 of муфты 2 and to shift it upwards on a shaft of a steering column. (Operated wheels should be in position of rectilinear movement). 4. An air cleaner. 5. To turn out both bolts 25, крепящих the internal ends of steering bent for рейке. Before вывертыванием bolts to unbend and remove a plate 24 which fixes heads of bolts. The plate 24 will not enclose to a reuse. 6. Демпфер a steering (if it is established on the car). 7. Both collars of fastening of the steering mechanism. 8. A sealing cover 3 from a shaft-gear wheel. 9. The steering mechanism in gathering through an aperture of a niche of the right wheel. The prevention If together with collars of fastening of the steering mechanism bolts have been dismantled, it is necessary to screw them into place and to tighten the moment of 20 Nanometers.

To establish or attach

Fastening of hinges of steering bent for рейке

23. STEERING DRAUGHT (LEFT) 24. THE FIXING PLATE 25. THE BOLT 26. THE BASIC PLATE 29. STEERING DRAUGHT (RIGHT) 32. CARTER'S CASING

Dismantle of steering draught

(ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)

AND. POSITION OF CUTS ON THE FIXING PLATE AT INSTALLATION CENTURY THE WRENCH WITH. FOR SIMPLIFICATION OF INSTALLATION TO APPLY A THIN FILM КОНСИСТЕНТНОЙ GREASINGS ON THE PLUG

(ONLY FOR CARS WITH THE MANUAL TRANSMISSION)

23. STEERING DRAUGHT (LEFT) 21. THE FIXING PLATE 25. THE BOLT 26. THE BASIC PLATE (ONLY FOR CARS WITH THE MANUAL TRANSMISSION) 27. THE PLUG OF THE HINGE OF STEERING DRAUGHT 30. THE WASHER 32. CARTER'S CASING 33. ДЕМПФЕР THE STEERING (ONLY FOR CARS WITH AUTOMATIC TRANSMISSION)

PERFORMANCE ORDER

1. The steering mechanism in gathering through an aperture of a niche of the right wheel. 2. A sealing cover 3 on a shaft-gear wheel. 3. Both collars of fastening of the steering mechanism. (It is necessary to use only new самоконтрящиеся nuts). 3атянуть nuts and bolts of fastening of collars of the steering mechanism the moment of 35 Nanometers. 4. Демпфер a steering (if it has been established on the car). 5. To establish two washers 30 which should be between a directing lath 10 and the internal ends of steering draughts. 6. To attach bolts 25 internal ends of steering draughts 23, 29 to directing lath 10. To tighten bolts of fastening of steering bent for рейке the steering mechanism the moment of 90 Nanometers. 7. To establish on a basic plate 26 and on heads of bolts 25 fixing plate 24. Cuts on a fixing plate should settle down how is shown on fig. Dismantle of steering draught. 8. To lower and put on муфту 2 the end of a shaft-gear wheel 5. To tighten fastening bolts муфты a steering shaft the moment of 25 Nanometers. 9. An air cleaner. 10. To lower the car. 11. To attach a negative wire of the storage battery.