Daewoo Nexia

Since 1994 of release

Repair and car operation



Дэу the Nexia
+ The maintenance instruction
+ Maintenance service
+ The engine
+ 3. The engine (two top camshafts)
+ Cooling system
+ Топлевная and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. The electronic block of management and gauges
+ Transmission
+ 10. A five-speed transmission and the main transfer RPO MM5
+ 11. Automatic Transmission
- Steering
   12.2. The general description
   12.3. The reechnyj steering mechanism in gathering
   12.4. Tips of steering draughts
   12.5. Steering draughts
   12.6. A casing картера the steering mechanism
   12.7. Муфта a steering shaft
   12.8. A sealing cover of an aperture of a forward board of the Body
   12.9. Плунжер рейки
   12.10. The Shaft-gear wheel
   12.11. Рейка
   12.12. The needle bearing
   12.13. The directing plug рейки
   12.14. Check of neutral position рейки
   12.15. Recommendations about replacement of consolidations in the hydraulic booster
   12.16. Check of level and having added a working liquid
   12.17. Removal of air from hydrosystem
   12.18. The steering mechanism with the hydraulic booster in gathering
   12.19. Hoses and pipelines
   12.20. A tank
   12.21. Tips of steering draughts
   12.22. Steering draughts
   12.23. Plugs of hinges of steering draughts
   12.24. Муфта a steering shaft
   12.25. A sealing cover
   12.26. Hydrocylinder pipelines
   12.27. Adjustment of a preliminary tightness of a spring плунжера
   12.28. Consolidations of a shaft of the hydrodistributor and the top bearing
   12.29. The steering mechanism
   12.30. Check of neutral position рейки
   12.31. A belt of a drive of the pump
   12.32. A pulley of a drive of the pump
   12.33. The pump in gathering
   12.34. Control levers on a steering column
   12.35. A steering wheel
   12.36. The ignition lock
   12.37. A steering column
   12.38. Lever the switch, a steering shaft, a steering column (noncontrollable)
   12.39. Lever the switch, a steering shaft, a steering column (regulated)
+ Running gear
+ 14. A forward suspension bracket
+ 15. A drive of forward wheels
+ 16. A back suspension bracket
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment






12.22. Steering draughts To remove or disconnect

PERFORMANCE ORDER
1. Fixing plate 37 from heads of bolts 38. A plate to throw out.
2. A bolt of 38 fastenings of the internal hinge of steering draught. If one steering draught is dismantled, to deduce a head of this draught from space between a basic plate 39 and a washer 29 and to remove draught. At simultaneous dismounting of both steering draughts it is necessary to screw after removal of the first draught into place a bolt 38 to keep mutual position рейки, a casing 44 and a directing lath.
3. To weaken a coupling bolt.
4. To remove steering draught.

To establish or attach

Installation of steering draughts

AND. THE ARRANGEMENT OF CUTS OF THE PLATE AT INSTALLATION

29. THE WASHER
35. STEERING DRAUGHT (LEFT)
37. THE FIXING PLATE
38. THE BOLT
39. THE BASIC PLATE
40. STEERING DRAUGHT (RIGHT)
44. CARTER'S CASING

PERFORMANCE ORDER
1. To screw in draught the adjusting screw. To tighten a bolt клеммового connections of steering draught by the moment of 22 Nanometers.
2. To insert into deepenings of a casing 44 and to centre concerning apertures of a washer 29.
3. To insert bolts 38 into apertures of a basic plate, further – in plugs of 36 hinges of steering draughts 35 and 40, in apertures of washers 29 and a directing lath 28 which is in a casing 44. To screw bolts 38 in рейку the steering mechanism. To tighten bolts of fastening of steering bent for рейке the steering mechanism the moment of 90 Nanometers.
4. To establish on heads of bolts 38 new fixing plate 37. To Pay attention to a correct arrangement of cuts of a plate.